Adjustment Items

01 Package Color Auto Adj.

This menu item is to be displayed on the machine mounted with Integrated Color Care Unit IQ-501.

Automatically adjust colors collectively.

-

02 Package Color Manual Adj.

Manually adjust color adjustment items collectively.

-

03 Density Balance Auto. Adj.

Perform the density balance adjustment using the scan function.

-

04 Maximum Density Adjustment

Adjust the maximum density for each of Y, M, C, and K colors. The machine will start the Gamma Automatic Adjustment after you change the maximum density. When the Gamma Automatic Adjustment is completed, proceed to the calibration with the image controller. Be sure to perform Color Density Manual Control after changing the maximum density.

Yellow: (Light) -10, -9, -8, -7, -6, -5, -4, -3, -2, -1, 0, +1, +2, +3, +4, +5, +6, +7, +8, +9, +10 (Dark)

Magenta: (Light)-10, -9, -8, -7, -6, -5, -4, -3, -2, -1, 0, +1, +2, +3, +4, +5, +6, +7, +8, +9, +10 (Dark)

Cyan: (Light)-10, -9, -8, -7, -6, -5, -4, -3, -2, -1, 0, +1, +2, +3, +4, +5, +6, +7, +8, +9, +10 (Dark)

Black: (Light)-10, -9, -8, -7, -6, -5, -4, -3, -2, -1, 0, +1, +2, +3, +4, +5, +6, +7, +8, +9, +10 (Dark)

05 Max. Density Auto Adj.

When Relay Unit RU-518 is mounted on the machine without Integrated Color Care Unit IQ-501, Max. Density Auto Adj. (RU) is displayed. If either optional unit is not mounted on the machine, this function is not displayed.

Automatically print and scan charts and then adjust the maximum density for each of Y, M, C, and K colors. When this adjustment is completed, proceed to the calibration with the image controller. Be sure to perform Color Density Manual Control after changing the maximum density. 

-

06 Color Density Control

Displayed when Integrated Color Care Unit IQ-501 or Relay Unit RU-518 is mounted on the machine.

Make settings for controlling the color density of output paper.

-

07 Periodical Both Sides Adj.

This menu item is to be displayed on the machine mounted with Integrated Color Care Unit IQ-501.

Configure settings for the periodical both-side adjustment.

Period. Both Sides Auto Adj.: ON, OFF

Adjustment Interval (100 to 9,999 sheets)

Deviation Check: ON, OFF

Specified Value (0.5 to 10.0 mm)

01 Printer Adjustment

01 Restart Timing Adjustment

Adjust the image position of lead edge in paper feed direction in the printer engine.

Prerequisite: FD-Mag. Adjustment is completed.

Objects of adjustment:

Restart Timing (Tray1), Restart Timing (Tray2), Restart Timing (Bypass Tray), Restart Timing (Tray3), Restart Timing (Tray4), Restart Timing (Tray5), Restart Timing (Tray6), Restart Timing (Tray7), Restart Timing (Tray8), Restart Timing (Tray9), Restart Timing (Tray10), Restart Timing (Tray11), Restart Timing (Back), Tray Large Plain Offset,, Tray Large Thick Offset, Tray Small Plain Offset, Tray Small Thick Offset, Bypass Large Plain Offset, Bypass Large Thick Offset, Bypass Small Plain Offset, Bypass Small Thick Offset, Large Plain Offset (ADU), Large Thick Offset (ADU), Small Plain Offset (ADU), Small Thick Offset (ADU)

Adj. Range: -60~+60 1 step = 0.1 mm

[-] Lower [+] Higher

02 Centering Adjustment

Adjust the image position in the crosswise direction of the printer engine.

Prerequisite: CD-Mag. Adjustment is completed.

Objects of adjustment:

Tray1, Tray2, Bypass Tray, Tray3, Tray4, Tray5, Tray6, Tray7, Tray8, Tray9, Tray10, Tray11, ADU, Tray1 Large Size Offset, Tray1 Small Size Offset, Tray1 8.5  5.5 Offset, Tray2 Large Size Offset, Tray2 Small Size Offset, Tray2 8.5  5.5 Offset, Bypass Tray Large Size Offset, Bypass Tray Small Size Offset, Bypass Tray 8.5  5.5 Offset , Tray3 Large Size Offset, Tray3 Small Size Offset, Tray4 Large Size Offset, Tray4 Small Size Offset, Tray5 Large Size Offset, Tray5 Small Size Offset, Tray6 Large Size Offset, Tray6 Small Size Offset, Tray7 Large Size Offset, Tray7 Small Size Offset, Tray8 Large Size Offset, Tray8 Small Size Offset, Tray9 Large Size Offset, Tray9 Small Size Offset, Tray10 Large Size Offset, Tray10 Small Size Offset, Tray11 Large Size Offset, Tray11 Small Size Offset, Large Plain Offset ADU, Large Thick Offset ADU, Small Plain Offset ADU, Small Thick Offset ADU, 8.5 5.5 Plain Offset ADU, 8.5 5.5 Thick Offset ADU

Adj. Range: -40~+40 1 step = 0.1 mm 

[-] Front [+] Back

03 FD-Mag. Adjustment

Adjust the magnification in paper feed direction in the printer engine.

Objects of adjustment:

Printer FD-Mag.

Adj. Range: -100~+100 1 step = 0.01%

Objects of adjustment:

Tray1 Offset (ADU), Tray2 Offset (ADU), Bypass Offset (ADU), Tray3 Offset (ADU), Tray4 Offset (ADU), Tray5 Offset (ADU), Tray6 Offset (ADU), Tray7 Offset (ADU), Tray8 Offset (ADU), Tray9 Offset (ADU), Tray10 Offset (ADU), Tray11 Offset (ADU)

Adj. Range: -80~+20 1 step = 0.01%

[-] Short [+] Long

04 CD-Mag. Adjustment

Adjust the magnification in crosswise direction in the printer engine.

Objects of adjustment: Printer CD-Mag., Tray1 Offset (ADU), Tray2 Offset (ADU), Bypass Offset (ADU), Tray3 Offset (ADU), Tray4 Offset (ADU), Tray5 Offset (ADU), Tray6 Offset (ADU), Tray7 Offset (ADU), Tray8 Offset (ADU), Tray9 Offset (ADU), Tray10 Offset (ADU), Tray11 Offset (ADU)

Adj. Range: -100~+100 1 step = 0.01%

[-] Short [+] Long

02 Scan Adjustment

01 Restart Timing Adjustment

Adjust the scan starting position when scanning the original on the original glass.

Prerequisite: FD-Mag. Adjustment is completed.

Adj. Range: -30~+30 1 step = 0.1 mm

[-] Image Slow [+] Image Fast

02 Centering Adjustment

Adjust the image position in the crosswise direction when scanning the original on the original glass.

Prerequisite: Printer Centering Adjustment is completed.

Objects of adjustment:

Orig. Glass Centering

Adj. Range: -57~+57 1 step = 0.1 mm

[-] Back [+] Front

03 FD-Mag. Adjustment

Adjust the magnification in feed direction when scanning the original on the original glass.

Prerequisite: Printer FD-Mag. Adjustment is completed.

Adj. Range: 990~1010 1 step = 0.001

[-] Short [+] Long

04 CD-Mag. Adjustment

Adjust the magnification in the crosswise direction when scanning the original from the original glass.

Prerequisite: Printer CD-Mag. Adjustment is completed.

Adj. Range: 990~1010 1 step = 0.001

[-] Short [+] Long

03 Stabilization Adj. Setting

Select Speed or Stability as job priority.

Speed or Stability

- If you select Stability, the productivity may drop.

- This selection is valid for jobs issued after change of this setting.

04 Execute Adjust Operation

Select a quality correction item and adjust the quality for your purpose.

Gamma Automatic Adj., Color Regist. Auto Adj., Toner Refresh Mode, Belt Refresh Mode

01 Staple Finisher Adjustment

01 Staple Finisher(Main)Adj.

01 Exit Guide Paper Width Adj.

Adjust the exit guide alignment pitch to be used by the staple finisher.

Make adjustment if output paper stack on main tray is uneven in straight delivery.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, SRA4 short edge feed, A4 long edge feed, A4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 12 18 short edge feed, 11 17 short edge feed, 9 11 long edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 8.5 14 short edge feed, 8 13 short edge feed, 13  19 short edge feed, B5 short edge feed, A6 short edge feed / Postcard, SRA4 long edge feed, B6, 16K short edge feed, Custom(380~488 mm), Custom(220~379 mm), Custom(139~219 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

[-] Wide [+] Narrow

02 Upper Gripper Operation

Select the upper gripper operation for main tray delivery exit.

Auto, ON, OFF

03 Output Alignment Operation

Select operation for output alignment.

Auto, ON, OFF

04 Staple Paper Width Adj.

Adjust the board alignment width of the staples in the staple finisher.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, SRA4 short edge feed, A4 long edge feed, A4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 12 18 short edge feed, 11 17 short edge feed, 9 11 long edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 8.5 14 short edge feed, 8 13 short edge feed, 13  19 short edge feed, SRA4 long edge feed, 16K short edge feed, Custom(380~488 mm), Custom(220~379 mm), Custom(139~219 mm)

Adj. Range: -20~+20 1 step = 0.1 mm

[-] Wide [+] Narrow

05 FD Alignment Plate Adj.

Adjust the vertical alignment fitting for staples in the staple finisher.

Objects of adjustment:

Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, 9 11 long edge feed, Custom(139~230 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

[-] Wide [+] Narrow

06 Staple Position Adjustment

Adjust 2 position staple pitch and corner staple positions in the staple finisher.

Objects of adjustment:

2 Position Pitch (120 mm), 2 Position Pitch (140 mm), 2 Position Pitch (165 mm), Rear Diagonal

Adj. Range: -5~+5 1 step = 1 mm

Objects of adjustment:

Rear Parallel, Front Parallel

Adj. Range: -3~+3 1 step = 1 mm

[-] Narrow [+] Wide

07 Rewind Paddle Descent Adj.

Adjust rewind paddle descent.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, SRA4 short edge feed, A4 long edge feed, A4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 12 18 short edge feed, 11 17 short edge feed, 9 11 long edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 8.5 14 short edge feed, 8 13 short edge feed, 13  19 short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(220~379 mm), Custom(139~219 mm)

Adj. Range: -10~+10 1 step = 0.2 mm

[-] Little [+] Much

08 Rewind Function Operation

Select operation for the rewind paddle.

Auto, ON, OFF

02 Staple Finisher(Fold)Adj.

This menu item is to be displayed and become configurable on Finisher FS-532 mounted with Saddle Stitcher SD-510.

01 Fold&Staple Paper Width Adj.

Adjust pitch of alignment plate in Saddle Stitcher SD-510 if half-folded or multi tri-folded paper show misalignment in the crosswise direction to paper feeding.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, 12  18 short edge feed, A3 short edge feed, 11  17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5  14 short edge feed, 8.5  11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8  13 short edge feed, 13  19 short edge feed, Custom(380~488 mm), Custom(240~379 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

[-] Narrow [+] Wide

02 Fold&Staple Pitch Adjustment

Adjust staple pitch in Saddle Stitcher SD-510. Make this adjustment if staple pitch is not within the allowance range.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, 12  18 short edge feed, A3 short edge feed, 11  17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5  14 short edge feed, 8.5  11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8  13 short edge feed, 13  19 short edge feed, Custom(380~488 mm), Custom(240~379 mm)

Adj. Range: -300~+300 1 step = 0.1 mm

Staple pitch: [-] Narrow [+] Wide

03 Fold&Staple Fold Position

Adjust half-fold position of fold & staple function in Saddle Stitcher SD-510. Make this adjustment if half-fold position is not within the specified range.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, 12  18 short edge feed, A3 short edge feed, 11  17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5  14 short edge feed, 8.5  11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8  13 short edge feed, 13  19 short edge feed, Custom(380~488 mm), Custom(240~379 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

Top face of output paper: [-] Extend [+] Shorten

04 Fold&Staple Staple Position

Adjust staple position in Saddle Stitcher SD-510.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, 12  18 short edge feed, A3 short edge feed, 11  17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5  14 short edge feed, 8.5  11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8  13 short edge feed, 13  19 short edge feed, Custom(380~488 mm), Custom(240~379 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

Top face of output paper: [-] Extend [+] Shorten

05 Half-Fold Fold Position Adj.

Adjust half-fold position of fold function in Saddle Stitcher SD-510.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, 12  18 short edge feed, A3 short edge feed, 11  17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5  14 short edge feed, 8.5  11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8  13 short edge feed, 13  19 short edge feed, Custom(380~488 mm), Custom(240~379 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

Top face of output paper: [-] Extend [+] Shorten

06 Tri-Fold Adjustment

01 Tri-Fold Position Adj.

Adjust Fold 1 and Fold 2 positions for multi tri-folding in Saddle Stitcher SD-510.

Make this adjustment if each fold position for tri-folding is not within the allowance range.

Objects of adjustment:

8.5 11 short edge feed, A4 short edge feed, 16K short edge feed

Fold 1, Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm

Fold 1: [-] Extend [+] Shorten

Fold 2: [-] Shorten [+] Extend

02 Double Fold Plate Adjustment

Adjust double fold plate in saddle stitcher.

Make the insertion deeper if the Fold 2 misalignment is large.

Objects of adjustment:

8.5 11 short edge feed, A4 short edge feed, 16K short edge feed

Adj. Range: -50~+50 1 step = 0.1 mm

Quantity of inserting double fold plate: [-] Shallow [+] Deep

07 Half-Fold Strength Adj.

To suppress the opening of booklets, increase the roller pressure time.

- You cannot adjust the strength to fold booklets.

- Long pressure time causes less productivity.

Adj. Range: 0~+10 1 step = 1 sec.

03 Staple Finisher(Punch)Adj.

This menu item is to be displayed and configurable on Finisher FS-532 mounted with Punch Kit PK-522.

01 Registration Adjustment

If the punch position is not parallel to the paper edge, control the paper curl and wrinkle by adjusting the paper loop amount of the registration roller.

Adj. Range: -50~+50 1 step = 0.1 mm

[-] Short [+] Long

02 Horizontal Position Adj.(FD)

Adjust the distance between the edge of the printed paper and the center of punch holes.

Objects of adjustment:

Offset for All Size, A3 short edge feed, A4 long edge feed, A4 short edge feed, SRA4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 8.5 14 short edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8 13 short edge feed, 5.5 8.5 long edge feed, 9 11 long edge feed, B5 short edge feed

Adj. Range: -50~+50 1 step = 0.1 mm

Punch position at paper edge: [-] Far [+] Close

03 Vertical Position Adj.(CD)

Adjust the misalignment in center positions of paper and punch holes for each paper size.

Objects of adjustment:

Offset for All Size, A3 short edge feed, A4 long edge feed, A4 short edge feed, SRA4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 8.5 14 short edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8 13 short edge feed, 5.5 8.5 long edge feed, 9 11 long edge feed, B5 short edge feed

Adj. Range: -50~+50 1 step = 0.1 mm

Punch position: [-] Forward [+] Backward

04 Staple Finisher(PI)Adj.

This menu item is to be displayed and configurable on Finisher FS-532 mounted with Post Inserter PI-502.

01 PI Registration Adjustment

When paper fed from the upper or lower tray of Post Inserter PI-502 has skew or wrinkle, or causes paper jam, adjust the paper loop of the registration roller.

Objects of adjustment:

PI Upper Tray, PI Lower Tray

Adj. Range: -5~+5 1 step = 1 mm

[-] Short [+] Long

01 Staple Finisher Adjustment

01 Staple Finisher(Main)Adj.

01 Exit Guide Paper Width Adj.

Adjust the exit guide alignment pitch to be used by the staple finisher.

Make adjustment if output paper stack on main tray is uneven in straight delivery.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, SRA4 short edge feed, A4 long edge feed, A4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 12 18 short edge feed, 11 17 short edge feed, 9 11 long edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 8.5  14 short edge feed, 8  13 short edge feed, 13  19 short edge feed, B5 short edge feed, A6 short edge feed / Postcard, SRA4 long edge feed, B6 short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(220~379 mm), Custom(139~219 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

[-] Wide [+] Narrow

02 Upper Gripper Operation

Select the upper gripper operation for main tray delivery exit.

Auto, ON, OFF

03 Output Alignment Operation

Select operation for output alignment.

Auto, ON, OFF

02 Multi Folder Adjustment

01 Multi Folder(Punch)Adj.

01 Paper Width Adjustment

Adjust the misalignment of punch hole positions.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, A4 long edge feed, A5 short edge feed, B5 long edge feed, A5 long edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8.5 11 long edge feed, 8 13 short edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 9 11 long edge feed

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the randomness [+] To reduce the tilts

02 Punch Vertical Position Adj.

01 2-Hole Punch

Adjust the vertical position of punch holes made by the folding unit.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, A4 long edge feed, A5 short edge feed, B5 long edge feed, A5 long edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8.5 11 long edge feed, 8 13 short edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 9 11 long edge feed

Adj. Range: -40~+40 1 step = 0.1 mm

[-] To move to the center [+] To move to the edge

02 3-Hole Punch

Adjust the vertical position of punch holes made by the folding unit.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, A4 long edge feed, B5 long edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 11 long edge feed, 8K short edge feed, 16K long edge feed, 9 11 long edge feed

Adj. Range: -40~+40 1 step = 0.1 mm

[-] To move to the center [+] To move to the edge

03 4-Hole Punch

Adjust the vertical position of punch holes made by the folding unit.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, A4 long edge feed, B5 long edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 11 long edge feed, 8K short edge feed, 16K long edge feed, 9 11 long edge feed

Adj. Range: -40~+40 1 step = 0.1 mm

[-] To move to the center [+] To move to the edge

02 Multi Folder(Fold)Adj.

01 Half-Fold Position Adj.

Adjust the folded position for half-fold.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom (380~458 mm), Custom (279~379 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

[-] To shorten the top face [+] To lengthen the top face

02 Z-Fold Position Adj.

Adjust the fold positions for Z-folding.

Adjust Fold 1to and Fold 2 in this order.

Objects of Adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom (380~458 mm), Custom (279~379 mm)

Fold 1, Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm

Fold 1: To narrow [-] <-> [+] To widen

Fold 2: To narrow [-] <-> [+] To widen 

03 Tri-Fold-in Pos. Adj.

Adjust the fold positions for tri-fold-in.

Adjust Fold 1to and Fold 2 in this order.

Objects of Adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom (380~458 mm), Custom (279~379 mm)

Fold 1, Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm

Fold 1: To narrow [-] <-> [+] To widen

Fold 2: To narrow [-] <-> [+] To widen

04 Tri-Fold-out Pos. Adj.

Adjust the fold positions for tri-fold-out.

Adjust Fold 1to and Fold 2 in this order.

Objects of Adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom (380~458 mm), Custom (279~379 mm)

Fold 1, Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm

Fold 1: To widen [-] <-> [+] To narrow

Fold 2: To narrow [-] <-> [+] To widen

05 Double Parallel Pos. Adj.

Adjust the fold positions for double parallel folding.

Adjust Fold 1to and Fold 2 in this order.

Objects of Adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom (380~458 mm), Custom (279~379 mm)

Fold 1, Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm

Fold 1: To narrow [-] <-> [+] To widen

Fold 2: To narrow [-] <-> [+] To widen

06 Gate Position Adj.

Adjust the gate position.

Adjust in order from Fold 1.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom (380~458 mm), Custom (279~379 mm)

Fold 1, Fold 2, Fold 3: Adj. Range: -50~+50 1 step = 0.1 mm

Fold 1: To narrow [-] <-> [+] To widen

Fold 2: To widen [-] <-> [+] To narrow

Fold 3: To narrow [-] <-> [+] To widen

03 Stacker Adjustment

01 Paper Width Adjustment

Adjust the position of adjustment plates if output sheets show misalignment in crosswise direction on the stacker tray.

Objects of adjustment:

Stacker No. 1, Stacker No. 2

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the dispersion [+] To reduce the distortion

02 Paper Length Adjustment

Adjust the position of the stopper if output sheets show misalignment in paper feed direction on the stacker tray.

Objects of adjustment:

Stacker No. 1, Stacker No. 2

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the dispersion [+] To reduce the distortion

04 Saddle Stitcher Adjustment

01 Fold Paper Width Adj.

Adjust the width of adjustment plates if half-folded or tri-folded sheets show misalignment.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~463 mm), Custom(257~379 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

[-] To reduce the misalignment [+] To reduce the distortion

02 Half-Fold Position Adj.

Adjust the fold position determined by the half-folder.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~463 mm), Custom(257~379 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

[-] To shorten the top face [+] To lengthen the top face

03 Staple Paper Width Adj.

Adjust the width of adjustment plates of the saddle stitcher to be used in Staple mode.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~463 mm), Custom(257~379 mm)

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the dispersion [+] To reduce the distortion

04 Staple Center Position

Adjust the center position of staples determined by the saddle stitcher.

Prerequisite: Staple paper width adjustment is completed.

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To move closer to paper center (fold) [+] To move away from paper center (fold)

05 Staple Pitch Adjustment

Adjust the staple pitch determined by the saddle stitcher.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~463 mm), Custom(257~379 mm)

Adj. Range: -20~+20 1 step = 1.0 mm

[-] To shorten [+] To lengthen

06 Trimming Adjustment

Adjust the trimming width.
The trim width should be more than 2.0 mm, otherwise the trimming operation may not be performed properly.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~463 mm), Custom(257~379 mm)

Adj. Range: -400~+400 1 step = 0.1 mm

[-] To narrow [+] To widen

07 Tri-Fold Position Adj.

Adjust the folded positions in Tri-Fold mode.

Set Fold 1toFold 2 in sequence.

Objects of adjustment:

Offset for All Size, A4 short edge feed, 8.5 11 short edge feed

Fold 1, Fold 2: Adj. Range: -100~+100 1 step = 0.1 mm

Fold 1: To widen [-] <-> [+] To narrow

Fold 2: To narrow [-] <-> [+] To widen

08 Trimmer Receiver Adj.

Frequent trimming operations may cause damage to the receiver, resulting in trimming failures. Move the receiver automatically or manually.

*Trimmer Receiver Adj. is not displayed by default. To use this setting, please contact your service representative.

Objects of adjustment: Trim Count

Adjustment range: 700 times, 500 times, 300 times

Objects of adjustment: Move Pitch

Adjustment range: 1.0 mm, 1.5 mm, 2.0 mm

Execute Compulsive Movement

04 Saddle Stitcher Adjustment

01 Fold Paper Width Adj.

Adjust the width of adjustment plates if half-folded or tri-folded sheets show misalignment.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, PI Paper, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed

Adj. Range: -50~+50 1 step = 0.1 mm

[-] To reduce the misalignment [+] To reduce the distortion

02 Fold Skew Adjustment

Adjust the skew of the folding line.

Objects of Adjustment:

Single Fold, Multi Fold: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, PI Paper, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed

Adj. Range: -50~+50 1 step = 0.1 mm

[-] To weaken [+] To strengthen

03 Half-Fold Position Adj.

Adjust the folded position for half-fold.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13  19 short edge feed

Adj. Range: -50~+50 1 step = 0.1 mm

[-] To shorten the top face [+] To lengthen the top face

04 Tri-Fold Position Adj.

Adjust the folded positions in Tri-Fold mode.

Adjust Fold 1to and Fold 2 in this order.

Objects of adjustment:

Offset for All Size, A4 short edge feed, 8.5 11 short edge feed

Fold 1: Offset for All Size, A4 short edge feed

Adj. Range: -100~+90 1 step = 0.1 mm

Fold 1: 8.5 11 short edge feed

Adj. Range: -100~+30 1 step = 0.1 mm

Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm

[-]: To narrow [+]: To widen

05 Crease Position Adjustment

Adjust the crease position.

01 Half-Fold Crease Position

Move the half-fold crease position.

Objects of Adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To shorten [+] To lengthen

02 Tri-Fold Crease Position

Move the tri-fold crease position.

Objects of Adjustment:

Fold 1, Fold 2: Offset for All Size, A4 short edge feed, 8.5 11 short edge feed

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To shorten [+] To lengthen

03 PB Cover Crease Position

Move the perfect binding cover crease position.

This menu item is to be displayed and allowed on the machine mounted with Perfect Binder PB-503.

Objects of Adjustment:

Crease Line 1, Crease Line 2: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13  19 short edge feed

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To shorten [+] To lengthen

06 Staple Paper Width Adj.

Adjust the width of adjustment plates of the saddle stitcher to be used in Staple mode.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13  19 short edge feed

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the dispersion [+] To reduce the distortion

07 Staple Center Position

Adjust the center position of staples determined by the saddle stitcher.

Prerequisite: Staple paper width adjustment is completed.

01 2 Position Staple

Adjust the center position for 2-position staple.

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To move rearward [+] To move frontward

02 4 Position Staple(Front 2)

Adjust the center position at two locations on the front edge for 4-position staple.

Objects of adjustment:

Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom(380~488 mm), Custom(257~379 mm)

Adj. Range: -100~+100 1 step = 0.1 mm

[-] To move rearward [+] To move frontward

03 4 Position Staple(Rear 2)

Adjust the center position at two locations on the rear edge for 4-position staple.

Objects of adjustment:

Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom(380~488 mm), Custom(257~379 mm)

Adj. Range: -100~+100 1 step = 0.1 mm

[-] To move rearward [+] To move frontward

08 Staple Pitch Adjustment

Adjust the staple pitch determined by the saddle stitcher.

01 2 Position Staple

Adjust the pitch for 2-position staple.

Objects of Adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed

Adj. Range: -20~+20 1 step = 1.0 mm

[-] To shorten [+] To lengthen

02 4 Position Staple(Front 2)

Adjust the pitch at two locations on the front edge for 4-position staple.

Objects of adjustment:

Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom(380~488 mm), Custom(257~379 mm)

Adj. Range: -10~+10 1 step = 1 mm

[-] To shorten [+] To lengthen

03 4 Position Staple(Rear 2)

Adjust the pitch at two locations on the rear edge for 4-position staple.

Objects of Adjustment:

Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom(380~488 mm), Custom(257~379 mm)

Adj. Range: -10~+10 1 step = 1 mm

[-] To shorten [+] To lengthen

09 Staple Offset Adjustment

Adjust the misalignment between the stapling positions and folding line.

Adj. Range: -10~+10 1 step = 0.1 mm

[-] To move leftward [+]: To move rightward

10 Staple Tip Adjustment

Change the staple leg shape.

Adj. Range: -9~+9 1 step = 1 msec

[-]: To be round [+] To be flat

11 Flattening a Fold(Strength)

Adjust the spine shape while changing the strength to form the book spine.

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To decrease the force [+] To increase the force

12 Flattening a Fold(Freq.)

Adjust the number of roller reciprocation times to form the book spine.

Adj. Range: -5~+5 1 step = 1

[-] To decrease [+] To increase

13 Parallel Trimming Adjustment

Adjust the levelness between the trimming line and cut edge.

Objects of Adjustment:

Front, Rear

Adj. Range: 0~+30 1 step = 0.1 mm

[Up the numerical value] To widen

[Down the numerical value] To narrow

14 Fore-edge Trimming Adj.

Adjust the trimming width.

The trimming width should be more than 5 mm, otherwise the trimming operation may not performed properly.

Objects of Adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed

Adj. Range: -400~+400 1 step = 0.1 mm

[-] To narrow [+] To widen

15 2-Side Slitting Adjustment

Adjust the 2-side slitting.

Objects of Adjustment:

Front, Rear

Adj. Range: -10~+10 1 step = 0.1 mm

[-] To narrow [+] To widen

16 2-Side Slit Finishing Adj.

Change the 2-side trimming speed to adjust skew and napping conditions.

Objects of adjustment:

61 g/m2 or Less, 62 g/m2 or More

Adj. Range: -4~+4 1 step = 5 mm/sec

[-] Slow (Reduct rough cut) [+] Fast (Reduce curve)

17 Trimmer Receiver Adj.

Frequent trimming operations may cause damage to the receiver, resulting in trimming failures. Move the receiver automatically or manually.

*Trimmer Receiver Adj. is not displayed by default. To use this setting, please contact your service representative.

Objects of adjustment: Trim Count

Adjustment range: 700 times, 500 times, 300 times

Objects of adjustment: Move Pitch

Adjustment range: 1.0 mm, 1.5 mm, 2.0 mm

Execute Compulsive Movement

05 Perfect Binder Adjustment

01 Sub Compile CD Width Adj.

Adjust misalignment or distortion in the crosswise direction of the body if detected. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, Custom(220~379 mm), Custom(148~219 mm)

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the distortion [+] To reduce the dispersion

02 Clamp CD Width Adjustment

Adjust misalignment or distortion in the crosswise direction of the body if detected. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, Custom(220~379 mm), Custom(148~219 mm)

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the distortion [+] To reduce the dispersion

03 Clamp FD Position Adj.

Adjust misalignment or distortion in the paper feed direction of the body if detected. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, Custom(220~379 mm), Custom(148~219 mm)

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the distortion [+] To reduce the dispersion

04 Glue Start Position

Adjust the position to start gluing on the body. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Ahead, Back: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, Custom(220~379 mm), Custom(148~219 mm)

Adj. Range: -128~+127 1 step = 0.1 mm

[-] To increase [+] To decrease

05 Glue Finish Position

Adjust the position to finish gluing on the body. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Ahead, Back: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, Custom(220~379 mm), Custom(148~219 mm)

Adj. Range: -128~+127 1 step = 0.1 mm

[-] To decrease [+] To increase

06 Cover Lead Edge Adj.

Adjust the position of the lead edge of the left cover sheet. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

PB Tray: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, Custom(220~379 mm), Custom(148~219 mm)

Except PB Tray: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, 5Custom(220~379 mm) , Custom(148~219 mm)

Adj. Range: -128~+127 1 step = 0.1 mm

[-] To move closer to the body [+] To move further from the body

07 Cover Trimming Adjustment

Adjust the trimming width of the right cover sheet. To align the lead edges of left and right cover pages, be sure to perform Cover Lead Edge Adjustment in advance.

Objects of adjustment:

Perfect Binder Tray, Except PB Tray

Adj. Range: -128~+127 1 step = 0.1 mm

[-] To narrow [+] To widen

08 Cover Up/Down CD Width Adj.

Adjust the misalignment between the cover sheet and body.

Objects of adjustment:

Perfect Binder Tray, Except PB Tray

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the distortion [+] To reduce the misalignment

09 Spine Corner Forming Pos.

Adjust the form of cover paper.

Objects of adjustment:

Up/Down Forward Adj. (Front), Up/Down Rear Adj. (Back)

Adj. Range: -128~+127 1 step = 0.1 mm

[-] To convex [+] To concave

10 Temperature Adjustment

Glue Tank -Low:

Adjust the temperature to control the tank heater.

(Temperature low) Down: viscosity increased

(Temperature high) Up: viscosity decreased

Glue Apply Roller:

Adjust the temperature to control the roller heater. This also supports heating of the glue.

(Temperature low) Down: viscosity increased

(Temperature high) Up: viscosity decreased

Object of Adjustment: Glue Tank -Low

Initial: 185°C

Adj. Range: 180~190 1 step = 1°C

Up: viscosity decreased, Down: viscosity increased

Object of Adjustment: Glue Apply Roller

Initial: 165°C

Adj. Range: 160~170 1 step = 1°C

Up: viscosity decreased, Down: viscosity increased

05 Finisher Adjustment

01 Fold & Staple Stopper

Adjust the staple positions in Fold & Staple mode.

(Finisher FS-612 only)

Objects of Adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, SRA3 short edge feed, Custom(380~458 mm), Custom(279~379 mm)

Adj. Range: -128~+127 1 step = 0.1 mm

[-] To move to the right [+] To move to the left

02 Half-Fold Stopper Adj.

Adjust the misalignment of the edges of printed paper.

(Finisher FS-612 only)

Objects of Adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, SRA3 short edge feed, Custom (380~458 mm), Custom (279~379 mm)

Adj. Range: -128~+127 1 step = 0.1 mm

[-] To lengthen the top face [+] To shorten the top face

03 Punch Adj. (Punch Kit PK-512 or Punch Kit PK-513)

This menu item is displayed and can be set when Punch Kit PK-512 or Punch Kit PK-513 is mounted on Finisher FS-531 or Finisher FS-612.

01 Vertical Position Adj.

Adjust the misalignment between the center of printed paper and the center of punch holes.

Objects of Adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, A4 short edge feed, A4 long edge feed, B5 short edge feed, B5 long edge feed, A5 short edge feed, A5 long edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8.5 11 long edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, 16K long edge feed, 9 11 long edge feed

Adj. Range: -50~+50 1 step = 0.1 mm

[-] To move closer to front edge [+] To move closer to rear edge

02 Horizontal Position Adj.

Adjust the distance from the edge of the printed paper to the center of punch holes.

Objects of Adjustment:

PI Tray, Main Body Tray

Adj. Range: -50~+50 1 step = 0.1 mm

[-] To shorten [+] To extend

03 Registration Adjustment

Adjust the registration loop amount if punch positions are inclined.

Objects of Adjustment:

Main Body/Reverse, Main Body/ADU, PI 1 Tray, PI 2 Tray

Adj. Range: -20~+20 1 step = 0.8 mm

04 Paper Edge Detect Sensor

Automatically adjust the sensitivity of the sensor so as to correctly detect the paper edge that is used as the reference for punch holes.

Start

04 Tri-Fold Adjustment

Adjust the first folded positions in Tri-Fold mode.

(Finisher FS-612 only)

Objects of Adjustment:

Offset for All Size, A4 short edge feed, 8.5 11 short edge feed, 16K short edge feed

Adj. Range: -128~+127 1 step = 0.1 mm

[-]: To widen [+]: To narrow

05 2 Pos. Staple Pitch Adj.

Adjust the staple pitch determined in Fold & Staple and Staple modes.

Objects of Adjustment:

Fold & Staple, Staple

Adj. Range: +128~+160 1 step = 1 mm

06 Post Inserter Tray Size

This menu item is displayed and can be set when Post Inserter PI-502 is mounted on Finisher FS-531 or Finisher FS-612.

Adjust the tray size of post inserter.

Objects of Adjustment:

A4 short edge feed, 8.5 11 short edge feed

Start

07 Output Quantity Limit

Specify the limit on output sheets.

When Finisher FS-531 is mounted

Objects of Adjustment:

Staple / 62 to 80 g/m2, Staple / 81 to 105 g/m2, Staple / 106 to 135 g/m2, Staple / 136 to 216 g/m2

Objects of Adjustment:

Staple / 62 to 80 g/m2

Adj. Range: +2~+50 1 step = 1 sheet

Objects of Adjustment:

Staple / 81 to 105 g/m2

Adj. Range: +2~+40 1 step = 1 sheet

Objects of Adjustment:

Staple / 106 to 135 g/m2

Adj. Range: +2~+30 1 step = 1 sheet

Objects of Adjustment:

Staple / 136 to 216 g/m2

Adj. Range: +2~+20 1 step = 1 sheet

When Finisher FS-612 is mounted

Objects of Adjustment:

Staple / 62 to 80 g/m2, Staple / 81 to 105 g/m2, Staple / 106 to 135 g/m2, Fold & Staple / 62 to 80 g/m2, Fold & Staple / 81 to 105 g/m2, Half-Fold / 62 to 105 g/m2, Tri-Fold / 62 to 80 g/m2

Objects of Adjustment:

Staple / 62 to 80 g/m2, Staple / 81 to 105 g/m2

Adj. Range: +2~+50 1 step = 1 sheet

Objects of Adjustment:

Staple / 106 to 135 g/m2

Adj. Range: 0, +2~+20 1 step = 1 sheet

Objects of Adjustment:

Fold & Staple / 62 to 80 g/m2, Fold & Staple / 81 to 105 g/m2

Adj. Range: +2~+20 1 step = 1 sheet

Objects of Adjustment:

Half-Fold / 62 to 105 g/m2, Tri-Fold / 62 to 80 g/m2

Adj. Range: +1~+3 1 step = 1 sheet

06: Relay Stacker (RU) Adjustment

01 Paper Width Adjustment

Adjust the alignment plate position in the crosswise direction of Relay Unit RU-510. Perform this adjustment when paper distortion or skew is detected in the finisher following Relay Unit RU-510.

For example, adjust a misalignment of punch holes in the crosswise direction.

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the randomness [+] To reduce the tilts

02 Paper Length Adjustment

Adjust the alignment plate position in the paper feed direction of Relay Unit RU-510. Perform this adjustment when paper distortion or skew is detected in the finisher following Relay Unit RU-510.
For example, adjust a misalignment of punch holes in the crosswise direction. 

Adj. Range: -50~+50 1 step = 0.1 mm

[-] To reduce the dispersion [+] To reduce the tilts

01 ADF Original Stop Pos. Adj.

Adjust the position to start scanning on the ADF and the image position in the crosswise direction.

Prerequisite: FD-Mag. Adjustment should be completed before adjusting the position to start scanning. Printer Centering Adjustment should be completed before adjusting the image position.

Objects of adjustment:

Restart Timing (Front), Restart Timing (Back)

Adj. Range: -40~+40 1 step = 0.1 mm

[-] Image Fast [+] Image Slow

Objects of adjustment:

Centering (Front), Centering (Back)

Adj. Range: -44~+44 1 step = 0.1 mm

[-] Front [+] Back

02 ADF Orig. Stop Pos. Auto

Automatically adjust the position to start scanning on the ADF and the image position in crosswise direction.

Prerequisite: FD-Mag. Adjustment should be completed before adjusting the position to start scanning. Printer Centering Adjustment should be completed before adjusting the image position.

Objects of adjustment:

Restart Timing (Front), Restart Timing (Back)
Centering (Front), Centering (Back)

03 FD-Mag. Adjustment

Adjust the magnification in paper feed direction when scanning on the ADF.

Prerequisite: Printer FD-Mag. Adjustment is completed.

Objects of adjustment:

ADF

Adj. Range: -20~+20 1 step = 0.1 %

[-] Short [+] Long

04 FD-Mag. Auto Adjustment

Automatically adjust the magnification in paper feed direction when scanning on the ADF.

Objects of adjustment:

ADF

05 Home Read Position Adj(Back)

Adjust the home position of the shading shaft to correct any image failure due to dirt on the shading shaft on the back side of the ADF.

Adj. Range: -4~+4 1 step = 1

06 FD-Mag. Adjustment(Back)

Adjust the magnification in paper feed direction on the back side when scanning on the ADF.

Prerequisite: Printer FD-Mag. Adjustment is completed.

Objects of adjustment:

ADF

Adj. Range: -20~+20 1 step = 0.1 %

[-] Short [+] Long

07 FD-Mag. Auto Adj.(Back)

Automatically adjust the magnification in paper feed direction on the back side when scanning on the ADF.

Objects of adjustment:

ADF

08 Main Scan Dir. Zoom(Back)

Adjust the magnification in crosswise direction on the back side when scanning on the ADF.

Prerequisite: Printer CD-Mag. Adjustment is completed.

Objects of adjustment:

ADF

Adj. Range: -10~+10 1 step = 0.1 %

[-] Short [+] Long

09 Main ScanDir.Zoom Auto(Back)

Automatically adjust the magnification in crosswise direction on the back side when scanning on the ADF.

Objects of adjustment:

ADF

10 Original Tray Pre-rise Set.

Adjust the standby position of the Original feed tray on the ADF.

Original Tray Pre-rise: ON, OFF

Objects of adjustment: Paper Tray

Adjustment range: (1-7)

Set the air assist setting for Paper Feed Unit PF-707m.

* This setting is not displayed by default. To use this setting, please contact your service representative.

Target Tray:

Tray 3, Tray 4, Tray 5, Tray 6, Tray 7, Tray 8, Tray 9, Tray 10, Tray 11

Setting Method:

Auto, Manual

Setting Range for Manual Adjustment:

Edge Airflow Setting: (Weak), 1, 2, 3, 4, 5, 6, 7, 8, 9 (Strong)

Side Airflow Setting: OFF, (Weak) 1, 2, 3, 4, 5, 6, 7, 8, 9 (Strong)